Ingersoll Rand Oil Filter 47705063001

The Ingersoll Rand Oil Filter 47705063001 is an oil filtration component for applicable compressor systems. MANN-FILTER identifies 47705063001 as an Ingersoll Rand OE number that cross-references to its WD 962/21 oil filter.

Oil filtration plays an important role in compressor maintenance. The oil filter removes contaminants from the lubrication circuit and helps maintain cleaner oil flow through the applicable system. Clean oil supports lubrication of important compressor components and helps maintain dependable operation.

Before ordering this filter, always compare the original part number and compressor information with the replacement specification.

Maintain Clean Compressor Oil

Compressor oil performs important lubrication and cooling functions inside an oil-injected compressor. Contaminated oil can carry unwanted particles through the lubrication circuit and potentially increase component wear.

An appropriate oil filter helps capture contaminants before they continue through the oil circuit. The 47705063001 provides a specific replacement identification for applicable Ingersoll Rand systems.

Regular filter replacement forms an important part of preventive compressor maintenance.

Match the 47705063001 Filter Specification

MANN-FILTER lists 47705063001 as an Ingersoll Rand OE reference for WD 962/21.

Available WD 962/21 specifications include:

• Ingersoll Rand OE Number: 47705063001
• MANN-FILTER Cross-Reference: WD 962/21
• Filter Type: Spin-on filter
• Height: 212 mm
• Outer Diameter: 93 mm
• Thread Size: 1-12 UNF
• Bypass Valve Opening Pressure: 2.5 bar
• Gasket Outside Diameter: 71 mm
• Gasket Inside Diameter: 62 mm

Use these specifications as identification references rather than assuming universal compatibility.

Support Effective Oil Filtration

A properly selected oil filter helps maintain the cleanliness of the compressor’s lubrication circuit. The filter media captures contaminants while allowing oil to continue through the system.

The correct filter should provide the required filtration characteristics without creating an unsuitable restriction in the oil circuit.

The 47705063001 / WD 962/21 cross-reference gives technicians a useful reference when identifying a replacement filter for an applicable compressor.

Replace the Oil Filter During Maintenance

Oil filters require periodic inspection and replacement according to the compressor manufacturer’s maintenance schedule.

Do not wait for severe contamination or an obvious filter problem before planning replacement. A preventive maintenance program allows technicians to replace filters at the appropriate service interval.

When replacing the filter, technicians should also inspect the sealing surface and check for signs of leakage around the filter connection.

Check the Filter Before Ordering

Part numbers provide an important starting point, but technicians should verify the complete application.

Before purchasing 47705063001, check:

• Compressor manufacturer
• Compressor model
• Compressor serial number
• Existing filter part number
• Filter height
• Filter diameter
• Thread specification
• Gasket dimensions
• Required bypass characteristics
• Compressor operating requirements

MANN-FILTER specifically lists 47705063001 as an Ingersoll Rand OE number, but its product page states that vehicle/application data are not available.

For this reason, model and serial verification remains important.

Match the 1-12 UNF Thread

The thread specification represents a critical part of filter compatibility. The WD 962/21 specification lists a 1-12 UNF thread.

A filter with a different thread may not install correctly, even if its overall dimensions appear similar.

Always compare the original filter’s thread and mounting arrangement before installation.

Never force a filter onto an incompatible mounting point.

Check the Filter Dimensions

Physical dimensions also help technicians identify the correct replacement.

The WD 962/21 cross-reference lists a 212 mm height and 93 mm outer diameter. Its gasket dimensions are also specified at 62 mm inside diameter and 71 mm outside diameter.

These measurements can help technicians compare the replacement with the original component.

However, dimensions alone do not establish compressor compatibility. Always verify the part number and equipment application.

Support Compressor Lubrication

The compressor lubrication system depends on clean and correctly circulated oil. Contaminants can affect lubricated components and contribute to wear when filtration and maintenance are inadequate.

A suitable oil filter supports the filtration stage of the lubrication circuit. By replacing the filter at the appropriate maintenance interval, technicians can help maintain the intended oil filtration process.

The 47705063001 Oil Filter should therefore be selected according to the compressor manufacturer’s recommended specifications.

Inspect for Oil Filter Problems

Technicians should inspect the oil filter and surrounding area during scheduled maintenance.

Potential warning signs include:

• Oil leakage
• Damaged filter housing
• Deformed filter body
• Incorrect installation
• Contaminated sealing surface
• Loose filter connection
• Unusual pressure-related symptoms

If the filter shows physical damage or leakage, investigate the cause before installing a replacement.

Install the Replacement Correctly

Correct installation helps prevent leakage and connection problems.

Before installation, clean the mating surface and inspect the sealing area. Confirm that the replacement filter matches the required thread and dimensions.

Follow the applicable compressor manufacturer’s installation procedure and tightening requirements. Avoid excessive tightening because incorrect installation can damage the seal or filter connection.

After installation, inspect the area for leakage during compressor operation.

Choose the Correct Ingersoll Rand Spare Part

The 47705063001 part number provides a useful identification reference for an applicable Ingersoll Rand oil filter. MANN-FILTER directly cross-references this number to WD 962/21.

Other public compressor-parts references also identify 47705063001 as an Ingersoll Rand oil filter.

However, aftermarket cross-reference databases can contain multiple alternative numbers. Treat cross-reference information as an identification aid and verify the original compressor application before ordering.

Maintain Your Compressor With the Right Filter

Regular oil filter replacement helps technicians maintain the compressor lubrication system and support planned maintenance.

Using the correct filter can simplify servicing because technicians can match the part number and technical specifications with the existing equipment.

For 47705063001, verify the WD 962/21 cross-reference, 212 mm height, 93 mm diameter, 1-12 UNF thread and applicable compressor model before placing an order.

Order Ingersoll Rand Oil Filter 47705063001

The Ingersoll Rand Oil Filter 47705063001 provides a clearly identifiable replacement reference for applicable compressor maintenance. MANN-FILTER identifies it as an OE number for WD 962/21, a spin-on oil filter.

For accurate part selection, provide the compressor model and serial number along with the existing filter part number.